fd(4)

NAME
     fd - floppy disk

DESCRIPTION
     The fd* devices refer to the Floppy  disk  driver  using  the  NEC  PD765
     floppy  disk controller.  These diskettes are arrays of 512 byte sectors,
     although Minix always works with two sectors at a time due  to  its  1024
     byte  block  size.   You  can  read or write any number of bytes however,
     Minix takes care of cutting and pasting incomplete blocks together.

     The driver is normally configured for two floppy  disk  devices  fd0  and
     fd1.  It can handle two more, but it is unlikely that the average PC can.

     On the first access to an fd device (by open(2) or mount(2)), the  driver
     will  execute  a series of read tests to determine the floppy type.  This
     works ok for all floppy types except the true 360k type,  because  it  is
     indistinguishable  from  the 720k type.  This only means that the size of
     the floppy is not estimated right.

     Bits 2-6 of the minor device number may be set to the floppy disk type to
     make  it  known  to  the  driver  what  type of diskette it is reading or
     writing.  The non-auto devices should be used for formatting, or when one
     wants  to  be  absolutely  sure that the device is accessed right.  These
     devices exist for drive 0:

         type   device   minor   media
          0      fd0      0      autodetect
          1      pc0      4      360k, 5.25"
          2      at0      8      1.2M, 5.25"
          3      qd0      12     360k in a 720k, 5.25" drive
          4      ps0      16     720k, 3.5"
          5      pat0     20     360k in a 1.2M, 5.25" drive
          6      qh0      24     720k in a 1.2M, 5.25" drive
          7      PS0      28     1.44M, 3.5"

     Type 4 may also be used for the rarely seen 720k, 5.25" floppies (type  2
     made  them  obsolete  fast.)   Note  that these "types" only describe the
     floppies from a software point of view, type 1 and 4 drives use the  same
     parameters.

     If the format bit (bit 7)  is  set,  then  the  driver  interprets  write
     commands  as  track  formatting  requests.  This is used by the format(1)
     command.

     If the type bits are set to 28, 29, 30, or 31, then  the  driver  uses  a
     partition  table  found  in  sector  0  to  partition  the  floppy.   The
     partitions  of  fd0  may  be  accessed  as  fd0p0  through  fd0p3.    See
     controller(4)  for  a  description of the partition table, and associated
     ioctl commands.

FILES
     /dev/fd[0-3],  /dev/pc[0-3],  /dev/at[0-3],  /dev/qd[0-3],  /dev/ps[0-3],
     /dev/pat[0-3], /dev/qh[0-3], /dev/PS[0-3], /dev/fd[0-3]p[0-3]

SEE ALSO
     format(1), controller(4), part(8).

BUGS
     The driver does not know the size of a 360k  diskette  in  a  360k  5.25"
     drive,  because  it  uses the 720k parameters for it.  So it will happily
     try to read past the end making all kinds of interesting noises.  It's  a
     good thing these drives are practically obsolete.

     The partition table is only read when the drive motor is off and only for
     an auto or partition device.  The driver assumes that a floppy in a drive
     with a running motor can't have been replaced all of a sudden.

AUTHOR
     Kees J. Bot (kjb@cs.vu.nl)